CogWikiEditor: /* Connections */

2026-09-03T16:23:24Z

Connections

← Older revision		Revision as of 16:23, 3 September 2026
Line 47:		Line 47:
	\|}		\|}

	[[File:Rotory-encoder-module-arduino.jpg\|thumb\|center\|~~900px~~\|Arduino motor speed measurement setup using an L293D driver and LM393 encoder]]		[[File:Rotory-encoder-module-arduino.jpg\|thumb\|center\|700px\|Arduino motor speed measurement setup using an L293D driver and LM393 encoder]]

	== Rotary Encoder ==		== Rotary Encoder ==

CogWikiEditor: /* Connections */

2026-09-03T16:23:12Z

Connections

← Older revision		Revision as of 16:23, 3 September 2026
Line 46:		Line 46:
	\| Push button / reset		\| Push button / reset
	\|}		\|}

			[[File:Rotory-encoder-module-arduino.jpg\|thumb\|center\|900px\|Arduino motor speed measurement setup using an L293D driver and LM393 encoder]]

	== Rotary Encoder ==		== Rotary Encoder ==

CogWikiEditor: /* Observation */

2026-09-03T16:19:53Z

Observation

← Older revision		Revision as of 16:19, 3 September 2026
Line 382:		Line 382:
	The Serial Monitor is set to '''115200 baud'''.		The Serial Monitor is set to '''115200 baud'''.

	When the encoder is rotated clockwise, the encoder position increases and the Serial Monitor displays:		When the encoder is rotated clockwise, the encoder position increases and the Serial Monitor displays: CLOCKWISE

	~~<center>~~		When the encoder is rotated counter-clockwise, the encoder position decreases and the Serial Monitor displays: COUNTER-CLOCKWISE
	~~'''CLOCKWISE'''~~
	~~</center>~~

	When the encoder is rotated counter-clockwise, the encoder position decreases and the Serial Monitor displays:

	~~<center>~~
	~~'''~~COUNTER-CLOCKWISE~~'''~~
	~~</center>~~

	The angle is calculated based on the encoder position and the specified '''20 pulses per revolution'''.		The angle is calculated based on the encoder position and the specified '''20 pulses per revolution'''.

CogWikiEditor: /* Arduino Rotary Encoder Position and Angle Measurement Using M274 / KY-040 */

2026-09-03T16:18:03Z

Arduino Rotary Encoder Position and Angle Measurement Using M274 / KY-040

← Older revision		Revision as of 16:18, 3 September 2026
Line 1:		Line 1:
	===Arduino Rotary Encoder Position and Angle Measurement Using M274 / KY-040===		===Arduino Rotary Encoder Position and Angle Measurement Using M274 / KY-040===

	~~{\| class="wikitable" style="float:right; margin-left:20px; width:300px;"~~
	~~! colspan="2" style="font-size:120%;" \| Rotary Encoder Measurement~~
	\|-
	~~! Controller~~
	~~\| Arduino UNO~~
	\|-
	~~! Encoder~~
	~~\| M274 / KY-040~~
	\|-
	~~! Encoder Pins~~
	~~\| CLK, DT, SW~~
	\|-
	~~! CLK Pin~~
	~~\| D2~~
	\|-
	~~! DT Pin~~
	~~\| D3~~
	\|-
	~~! SW Pin~~
	~~\| D4~~
	\|-
	~~! Resolution~~
	~~\| 20 pulses/revolution~~
	\|-
	~~! Output~~
	~~\| Position, Angle, Direction~~
	\|}

	'''Arduino Rotary Encoder Position and Angle Measurement''' is a rotary encoder interfacing setup using an Arduino UNO and an M274 / KY-040 rotary encoder.		'''Arduino Rotary Encoder Position and Angle Measurement''' is a rotary encoder interfacing setup using an Arduino UNO and an M274 / KY-040 rotary encoder.

CogWikiEditor: Created page with "===Arduino Rotary Encoder Position and Angle Measurement Using M274 / KY-040=== {| class="wikitable" style="float:right; margin-left:20px; width:300px;" ! colspan="2" style="font-size:120%;" | Rotary Encoder Measurement |- ! Controller | Arduino UNO |- ! Encoder | M274 / KY-040 |- ! Encoder Pins | CLK, DT, SW |- ! CLK Pin | D2 |- ! DT Pin | D3 |- ! SW Pin | D4 |- ! Resolution | 20 pulses/revolution |- ! Output | Position, Angle, Direction |} '''Arduino Rotary Encoder P..."

2026-09-03T16:17:51Z

Created page with "===Arduino Rotary Encoder Position and Angle Measurement Using M274 / KY-040=== {| class="wikitable" style="float:right; margin-left:20px; width:300px;" ! colspan="2" style="font-size:120%;" | Rotary Encoder Measurement |- ! Controller | Arduino UNO |- ! Encoder | M274 / KY-040 |- ! Encoder Pins | CLK, DT, SW |- ! CLK Pin | D2 |- ! DT Pin | D3 |- ! SW Pin | D4 |- ! Resolution | 20 pulses/revolution |- ! Output | Position, Angle, Direction |} '''Arduino Rotary Encoder P..."

New page

===Arduino Rotary Encoder Position and Angle Measurement Using M274 / KY-040===

{| class="wikitable" style="float:right; margin-left:20px; width:300px;"
! colspan="2" style="font-size:120%;" | Rotary Encoder Measurement
|-
! Controller
| Arduino UNO
|-
! Encoder
| M274 / KY-040
|-
! Encoder Pins
| CLK, DT, SW
|-
! CLK Pin
| D2
|-
! DT Pin
| D3
|-
! SW Pin
| D4
|-
! Resolution
| 20 pulses/revolution
|-
! Output
| Position, Angle, Direction
|}

'''Arduino Rotary Encoder Position and Angle Measurement''' is a rotary encoder interfacing setup using an Arduino UNO and an M274 / KY-040 rotary encoder.

The encoder provides two digital signals, '''CLK''' and '''DT''', which are used by the Arduino to determine the direction and position of rotation.

The encoder also includes a push button '''SW'''. Pressing the button resets the encoder position to zero.

The program uses a typical encoder resolution of '''20 pulses per revolution''' to calculate the approximate shaft angle.

<center>
'''Rotary Encoder → Arduino UNO → Position + Angle + Direction'''
</center>

== Connections ==

{| class="wikitable"
! Device
! Pin
! Arduino UNO
! Function
|-
| M274 / KY-040
| + / VCC
| 5V
| Power
|-
| M274 / KY-040
| GND
| GND
| Ground
|-
| M274 / KY-040
| CLK
| D2
| Encoder clock signal
|-
| M274 / KY-040
| DT
| D3
| Encoder direction signal
|-
| M274 / KY-040
| SW
| D4
| Push button / reset
|}

== Rotary Encoder ==

The M274 / KY-040 rotary encoder provides two output signals:

* '''CLK''' – Clock signal
* '''DT''' – Direction signal

The Arduino reads the relationship between the '''CLK''' and '''DT''' signals to determine whether the encoder is rotating clockwise or counter-clockwise.

The encoder also provides a push button through the '''SW''' pin.

The program assumes:

<center>
'''20 pulses = 1 revolution'''
</center>

== Encoder Resolution ==

The program defines the encoder resolution as:

<center>
<code>PULSES_PER_REV = 20</code>
</center>

Therefore, one complete revolution corresponds to approximately '''20 encoder pulses'''.

The angle corresponding to the encoder position is calculated using:

<center>
<code>Angle = (Pulses in One Revolution × 360) / 20</code>
</center>

Therefore:

<center>
'''1 pulse ≈ 18°'''
</center>

== Encoder Direction ==

The Arduino detects a falling edge of the '''CLK''' signal.

At the falling edge, the Arduino checks the state of the '''DT''' signal.

If DT is HIGH:

<center>
'''Clockwise → Position increases'''
</center>

If DT is LOW:

<center>
'''Counter-clockwise → Position decreases'''
</center>

The encoder position is stored in:

<pre>
volatile long encoderPosition = 0;
</pre>

Clockwise rotation increments the position, while counter-clockwise rotation decrements it.

== Push Button Reset ==

The '''SW''' pin is connected to Arduino '''D4'''.

The input uses the Arduino's internal pull-up resistor:

<pre>
pinMode(SW_PIN, INPUT_PULLUP);
</pre>

When the button is pressed, the SW pin becomes '''LOW'''.

The program then resets:

<center>
'''Position = 0'''<br>
'''Angle = 0°'''
</center>

A debounce time of '''200 ms''' is used to prevent multiple resets caused by button bouncing.

== Working ==

The Arduino continuously performs the following operations:

# Reads the CLK and DT signals from the rotary encoder.
# Detects changes in the CLK signal using an interrupt.
# Determines the direction of rotation using the DT signal.
# Increments or decrements the encoder position.
# Calculates the angle corresponding to the current position.
# Displays the position, angle and direction on the Serial Monitor.
# Checks the push button on '''D4'''.
# Resets the encoder position to zero when the button is pressed.

The overall operation is:

<center>
'''CLK + DT → Direction → Position → Angle'''
</center>

== Interrupt Operation ==

The '''CLK''' signal is connected to Arduino '''D2'''.

On the Arduino UNO, D2 supports an external interrupt.

The program attaches the interrupt using:

<pre>
attachInterrupt(
digitalPinToInterrupt(CLK_PIN),
encoderISR,
CHANGE
);
</pre>

The encoder interrupt function reads both '''CLK''' and '''DT''' signals and determines the direction of rotation.

The interrupt is triggered whenever the CLK signal changes.

== Angle Calculation ==

The program calculates the position within one complete revolution using the modulo operation:

<pre>
long pulsesInOneRev = position % PULSES_PER_REV;
</pre>

For negative positions, the program adjusts the value so that the angle remains within the range of '''0° to 360°'''.

The angle is then calculated as:

<center>
<code>Angle = (pulsesInOneRev × 360.0) / PULSES_PER_REV</code>
</center>

With '''20 pulses per revolution''':

<center>
'''20 pulses → 360°'''<br>
'''10 pulses → 180°'''<br>
'''5 pulses → 90°'''<br>
'''1 pulse → 18°'''
</center>

== Serial Monitor ==

The Serial Monitor is set to '''115200 baud'''.

At startup, the program displays:

<pre>
M274 Rotary Encoder Test
------------------------
Rotate the encoder...
</pre>

During rotation, the program displays the encoder position, angle and direction.

Example:

<pre>
Position: 1 | Angle: 18.0 deg | Direction: CLOCKWISE
Position: 2 | Angle: 36.0 deg | Direction: CLOCKWISE
Position: 3 | Angle: 54.0 deg | Direction: CLOCKWISE
Position: 2 | Angle: 36.0 deg | Direction: COUNTER-CLOCKWISE
</pre>

When the push button is pressed:

<pre>
RESET -> Position = 0, Angle = 0 deg
</pre>

== Arduino Code ==

<pre>
/*
M274 / KY-040 Rotary Encoder
Arduino UNO

Connections:
----------------------------
M274 Arduino UNO
----------------------------
+ / VCC -> 5V
GND -> GND
CLK -> D2
DT -> D3
SW -> D4

Typical encoder resolution:
20 cycles/pulses per revolution

Features:
- Detects clockwise rotation
- Detects counter-clockwise rotation
- Counts encoder position
- Calculates approximate angle
- Push button resets position to zero
*/

#define CLK_PIN 2
#define DT_PIN 3
#define SW_PIN 4

// Typical M274/KY-040 specification
const int PULSES_PER_REV = 20;

// Encoder position
volatile long encoderPosition = 0;

// Previous CLK state
volatile bool lastCLKState = HIGH;

// Button debounce
unsigned long lastButtonTime = 0;
const unsigned long debounceTime = 200;

// Encoder interrupt function
void encoderISR()
{
bool currentCLK = digitalRead(CLK_PIN);
bool currentDT = digitalRead(DT_PIN);

// Detect falling edge of CLK
if (lastCLKState == HIGH && currentCLK == LOW)
{
if (currentDT == HIGH)
{
// Clockwise
encoderPosition++;
}
else
{
// Counter-clockwise
encoderPosition--;
}
}

lastCLKState = currentCLK;
}

void setup()
{
Serial.begin(115200);

// Internal pull-up resistors
pinMode(CLK_PIN, INPUT_PULLUP);
pinMode(DT_PIN, INPUT_PULLUP);
pinMode(SW_PIN, INPUT_PULLUP);

// Read initial CLK state
lastCLKState = digitalRead(CLK_PIN);

// Interrupt on CLK
attachInterrupt(
digitalPinToInterrupt(CLK_PIN),
encoderISR,
CHANGE
);

Serial.println("M274 Rotary Encoder Test");
Serial.println("------------------------");
Serial.println("Rotate the encoder...");
}

void loop()
{
// Read encoder position safely
noInterrupts();
long position = encoderPosition;
interrupts();

// Calculate angle
long pulsesInOneRev = position % PULSES_PER_REV;

if (pulsesInOneRev < 0)
{
pulsesInOneRev += PULSES_PER_REV;
}

float angle =
(pulsesInOneRev * 360.0) / PULSES_PER_REV;

// Display data
static long previousPosition = 999999;

if (position != previousPosition)
{
Serial.print("Position: ");
Serial.print(position);

Serial.print(" | Angle: ");
Serial.print(angle, 1);

Serial.print(" deg | Direction: ");

if (position > previousPosition)
{
Serial.println("CLOCKWISE");
}
else
{
Serial.println("COUNTER-CLOCKWISE");
}

previousPosition = position;
}

if (digitalRead(SW_PIN) == LOW)
{
if (millis() - lastButtonTime > debounceTime)
{
noInterrupts();
encoderPosition = 0;
interrupts();

Serial.println("RESET -> Position = 0, Angle = 0 deg");

lastButtonTime = millis();
}
}
}
</pre>

== Observation ==

The Serial Monitor is set to '''115200 baud'''.

When the encoder is rotated clockwise, the encoder position increases and the Serial Monitor displays:

<center>
'''CLOCKWISE'''
</center>

When the encoder is rotated counter-clockwise, the encoder position decreases and the Serial Monitor displays:

<center>
'''COUNTER-CLOCKWISE'''
</center>

The angle is calculated based on the encoder position and the specified '''20 pulses per revolution'''.

Pressing the encoder push button resets the position and angle to zero.

== Result ==

The Arduino UNO successfully interfaces with the '''M274 / KY-040 rotary encoder''' and detects clockwise and counter-clockwise rotation.

The program counts the encoder position, calculates the approximate angular position based on '''20 pulses per revolution''', displays the direction and angle on the Serial Monitor, and resets the position to zero when the push button is pressed.

Rotary Encoder Module - Revision history

CogWikiEditor: /* Connections */

CogWikiEditor: /* Connections */

CogWikiEditor: /* Observation */

CogWikiEditor: /* Arduino Rotary Encoder Position and Angle Measurement Using M274 / KY-040 */